facebook  twitter  linkedin  pinterest  tumblr
Service Hotline
+86-13510974563
Tel:86-755-28772795
Email: sales@halnziye.com
搜索
Search
About Us
联系我们
Check category
/
/
/
Thermal Grease Standard Test Method ASTM-D5470

Thermal Grease Standard Test Method ASTM-D5470

  • Categories:Events
  • Author:
  • Origin:
  • Time of issue:2016-12-27 00:00
  • Views:

(Summary description)

Thermal Grease Standard Test Method ASTM-D5470

(Summary description)

  • Categories:Events
  • Author:
  • Origin:
  • Time of issue:2016-12-27 00:00
  • Views:
Information
Standard Test Method for Thermal Transmission Properties of Thermally Conductive Electrical Insulation Materials
----ASTM-D5470
 
Significance and Use
 
ASTM-D5470 measures the steady state thermal impedance of electrical insulating materials(most of the thermal interface materials including thermal grease&thermal pad&thermal glue and phase change materials) used to enhance heat transfer in electrical and electronic applications. This standard is especially useful for measuring thermal transmission properties of specimens that are either too thin or have insufficient mechanical stability to allow placement of temperature sensors in the specimen as in Test Method E1225.
 
This standard imposes an idealized heat flow pattern and specifies an average specimen test temperature. The thermal impedances thus measured cannot be directly applied to most practical applications where these required uniform, parallel heat conduction conditions do not exist.
 
This standard is useful for measuring the thermal impedance of the following material types.
 
Type I—Viscous liquids that exhibit unlimited deformation when a stress is applied. These include liquid compounds such as greases, pastes, and phase change materials. These materials exhibit no evidence of elastic behavior or the tendency to return to initial shape after deflection stresses are removed.
 
Type II—Viscoelastic solids where stresses of deformation are ultimately balanced by internal material stresses thus limiting further deformation. Examples include gels, soft, and hard rubbers. These materials exhibit linear elastic properties with significant deflection relative to material thickness.
 
Type III—Elastic solids which exhibit negligible deflection. Examples include ceramics, metals, and some types of plastics.
Scope
 
1.This standard covers a test method for measurement of thermal impedance and calculation of an apparent thermal conductivity for thermally conductive electrical insulation materials ranging from liquid compounds to hard solid materials.
 
2. The term “thermal conductivity” applies only to homogeneous materials. Thermally conductive electrical insulating materials are usually heterogeneous and to avoid confusion this test method uses “apparent thermal conductivity” for determining thermal transmission properties of both homogeneous and heterogeneous materials.
 
3. The values stated in SI units are to be regarded as standard.
 
4. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
 
The apparent thermal conductivity of a specimen can be calculated from the measured thermal impedance and measured specimen thickness if the interfacial thermal resistance is insignificantly small (nominally less than 1 %) compared to the thermal resistance of the specimen.
 
The apparent thermal conductivity of a sample material can be accurately determined by excluding the interfacial thermal resistance. This is accomplished by measuring the thermal impedance of different thicknesses of the material under test and plotting thermal impedance versus thickness. The inverse of the slope of the resulting straight line is the apparent thermal conductivity. The intercept at zero thickness is the sum of the contact resistances at the two surfaces.
 
The contact resistance can be reduced by applying thermal grease or oil to the test surfaces of rigid test specimens (Type III).
Keyword:

Scan the QR code to read on your phone

+86-755-28772795
Add: 3-4/F Bld.D Hehengxing Sci&Tech Park,No.19 Minqing Road,Longhua
District,Shenzhen China
Fax:+86-755-28772796
Email:sales@halnziye.com

Copyright© Shenzhen Halnziye Electronics Co.,Ltd 粤ICP备09218394号 深圳市市场监督管理局企业主体身份公示 Powered by www.300.cn